42 not categorized PORSCHE 996 BUSHINGS SUSPENSIONCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1978-83 (includes uncategorized and accessory items) FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$273.90
Make a selection FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$261.80
Make a selection FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$69.30
Make a selection FVD33300909ATK This non-adjustable rear spring plate is remanufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car. This part is a remanufactured part. Send us your original and we will have it remanufactured for you. We do not offer a core exchange on this part. Each is remanufactured in Germany, so the lead times can vary.
$342.10
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$482.89
Make a selection FVD34101702RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and r...(choose a part on the right to read more)
$440.00
Make a selection MB1230 The Porsche 911 came equipped from the factory for high performance cornering -- but some things have changed in the almost 40 years the 911 has been on the road. For one, the rubber suspension bushings that monoballs replace are most likely already worn out or cracked from decades of use. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$273.90
Make a selection RMB11 The Porsche 911 came equipped from the factory for high performance cornering -- but some things have changed in the almost 40 years the 911 has been on the road. For one, the rubber suspension bushings that monoballs replace are most likely already worn out or cracked from decades of use. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$273.90
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$715.00
Make a selection FVD33150010 Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set. 1 kit is necessary per car. Please note: we recommend this kit for race use, as noise may resonate inside the cabin during street use. For those that are concerned about the noise, please order part # FVD3310212291
$704.00
Make a selection FSBA22 The light-weight hollow sway bars are half the weight of a solid bar with the same stiffness. they are fabricated from aircraft-quality 4130 chrome moly alloy steel and heat treated to maximize strength and reliability.
$495.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |